Burs, handpieces, abrasives and polishing
- Dental material
Teeth are cut with burs in high- and low-speed handpieces, cooled with water to protect the pulp. Polishing leaves restorations smooth so plaque cannot stick.
What it is
High-speed air-turbine or electric handpieces cut enamel and dentine efficiently with diamond or tungsten carbide burs; low-speed handpieces remove soft caries and finish. Diamond burs abrade; carbide burs cut with blades. Water spray prevents heat damage to the pulp. Finishing and polishing use progressively finer abrasives (discs, strips, rubber points, pastes) to remove excess, refine contour and leave a smooth, glossy surface.
Composition and properties
- High speed for enamel and old restorations; low speed for caries and finishing near the pulp.
- Water cooling is essential: dry cutting overheats the pulp.
- Worn burs cut poorly and heat more: replace them.
- Polished surfaces collect less plaque and stain and wear opposing teeth less.
- Handpieces are heat-sterilised between patients and generate aerosols.
| Tool | How it removes tissue | Best for | Watch out |
|---|---|---|---|
| Diamond bur | Abrades with bonded diamond grit | Enamel, ceramics, crown preparations | Leaves a rougher surface; clogs and heats when worn |
| Tungsten carbide bur | Cuts with blades | Dentine, removing old fillings, fine finishing | Dulls and heats when worn |
| Steel or carbide round bur at low speed | Cuts slowly with blades | Removing soft caries near the pulp | Less efficient on enamel |
| Polishers: discs, strips, rubber points, pastes | Progressively finer abrasion | A smooth, glossy finish | Skipping grades leaves scratches |
Uses, limits and safety
- Excessive pressure, worn burs and dry cutting cause pulpitis after preparation.
- Rough restoration margins trap plaque and cause recurrent caries and gingivitis.
- Lubricate and maintain handpieces as the manufacturer directs.
Next step / Initial management
- Use water spray and light, intermittent pressure when cutting.
- Sensitivity or pain after a new restoration: refer back to the dentist to check finishing and the pulp.
- Rough or overhanging margins seen on examination: refer for refinishing.
Common traps
- Higher speed is what overheats the tooth: heat comes mainly from dry cutting, heavy pressure and worn burs; water spray protects the pulp
- Polishing is only cosmetic: smooth surfaces collect less plaque and stain and wear opposing teeth less
- A worn bur works if pressed harder: worn burs cut poorly and heat the tooth, so they are replaced
- Handpieces only need wiping between patients: they are heat-sterilised between patients and they generate aerosols
Test yourself
Think of the answer, then tap the question to see it.
Why is water spray used with high-speed handpieces?
To cool the tooth and prevent heat damage to the pulp.
What is the difference between diamond and carbide burs?
Diamond burs abrade with bonded particles; tungsten carbide burs cut with blades.
Why are restorations polished?
Smooth surfaces collect less plaque and stain and wear opposing teeth less.
A patient has lingering sensitivity after a crown preparation cut with heavy pressure and little water. What likely happened?
Heat injury to the pulp from dry, high-pressure cutting; refer back to the dentist to monitor pulp vitality.
A 35-year-old's new composite has a rough margin that catches floss. Why does it matter?
Rough or overhanging margins trap plaque, causing gingivitis and recurrent caries; refer for refinishing and polishing.
Connections
Educational content; it does not replace assessment by a dentist or doctor and is not a clinical instruction. For facial or neck swelling with difficulty swallowing or breathing, a knocked-out tooth or bleeding that will not stop, go to an emergency department at once.
Sources: Aerosol and splatter generation with rotary handpieces used in restorative and orthodontic dentistry: a systematic review (BDJ Open (PMC open access), 2022); Oral Surgery, Instruments (StatPearls Publishing (NCBI Bookshelf), 2022); Dental Infection Control (StatPearls Publishing (NCBI Bookshelf), 2023).
Spotted a mistake?We are always improving for the community. Tell us what is wrong and our team will review it.Report a mistake
Representative model, for educational purposes only.
